13 Search Results

Combustion-based transportation, electricity generation, and industrial heating in manufacturing constitute the three largest sectors of energy demand. Some of the recent technology development in these sectors are: switching to low-carbon fuels for the transportation sector, increasing energy efficiency in the power sector, and capturing carbon emissions from conventional power generators. Several teams at the National Renewable Energy Laboratory have been actively advancing research in these areas by leveraging computational modeling of combustion processes across the heavy-duty land based transportation, aviation, and power generation sectors. This article summarizes some of these efforts, demonstrating the potential of advanced computational techniques to generatemore » technological solutions that will transform the global energy system.« less

Low-temperature gasoline combustion (LTGC) with additive-mixing fuel injection (AMFI) is a new combustion strategy that has been demonstrated to deliver 9%–25% better brake thermal efficiency than similar-sized market-leading diesel engines over the operating map. Moreover, the LTGC-AMFI engine shows near-zero smoke, and NOx emissions are 4–100 times lower than those of a diesel, sufficiently low that no aftertreatment, or only passive NOx aftertreatment, would be sufficient (diesel exhaust fluid is not required). LTGC-AMFI combustion is based on kinetically controlled compression ignition of a dilute charge with a variable amount of low-to-moderate fuel stratification. Fast combustion control is provided by addingmore » minute amounts of an ignition-enhancing additive into the fuel each engine cycle to control its reactivity. This strategy was used to operate a medium-duty (MD) LTGC-AMFI engine at loads from idle to 16.3 bar BMEP and speeds from 600 to 2400 rpm with regular E10 gasoline, which covers nearly the entire operating map of a typical MD engine. Turbine-out temperatures were sufficient for an oxidation catalyst to control hydrocarbon and CO emissions. Autonomie simulations over the GEM ARB Transient and the GEM 55 mph Cruise driving cycles for class-6 trucks using this technology showed fuel economies of 8.1 and 11.4 mpg-gasoline-equivalent, respectively, corresponding to 18.6% and 13.4% improvements over a similar-size diesel engine. Engine-out NOx emissions were 0.024 and 0.01 g/bhp-h, respectively, well below current U.S. emission standards. These results show that switching from diesel to LTGC-AMFI engines would greatly reduce greenhouse gas (GHG) emissions for off-road, MD and HD applications, which will continue to rely on combustion engines because electrification is not practical in the foreseeable future. Finally, with their reduced fuel consumption, the lower cost of gasoline compared to diesel fuel, and much lower aftertreatment costs, LTGC-AMFI engines also offer a significantly lower total cost of ownership.« less

Here, this paper explores the performance characteristics of a compression ignition HYUNDAI 2.2L engine operating with Dimethyl Ether (DME). Test are carried out at three operating conditions that weigh heavily in the FTP75 certification cycle (1000rpm-12Nm, 1500rpm-50Nm, 2000rpm-100Nm). The engine features a high-pressure common rail fuel injection system designed to operate with liquified gases. The main component of the fuel system is a high-pressure pump that incorporates an electronic inlet metering valve commanded on a crank-angle base to control the rail pressure. The pump, which requires no pressure regulator, provides the flow needed to the injectors without flow returning tomore » the inlet. This novel fueling system is leveraged in tests that are conducted to examine the impact of EGR, combustion phasing, injection pressure on efficiency and emissions. In addition, the impact of introducing 15% Propane by mass is examined. During the tests, the engine ECU is aided by an Engine Controller High Speed Oversight unit (ECHO) to provide combustion phasing control, improved cylinder-to-cylinder uniformity, and an effective optimization over the testing effort. The use of DME and Propane allowed for peak thermal efficiency of nearly 43%. These fuels enable significant carbon index (CI) reductions over the baseline Diesel fuel, with indications that 50% reduction in CO₂ over the Diesel engine are possible.« less

Increasing engine efficiency is essential to reducing emissions, which is a priority for automakers. Unconventional modes such as boosted and highly dilute operation have the potential to increase engine efficiency but suffer from stability concerns and cyclic variability. To aid engineers in designing ignition systems that reduce cyclic variability in such engine operation modes, reliable and accurate spark-ignition models are necessary. Here, in this article, a Lagrangian–Eulerian spark-ignition (LESI) model is used to simulate electrical discharge, spark channel elongation, and ignition in inert or reacting crossflow within a combustion vessel, at different pressures, flow speeds, and dilution rates. First themore » model formulation is briefly revisited. Then, the experimental and simulations setups are presented. The results showcase the model’s ability to predict the secondary circuit voltage, current, and power signals, in addition to the spark channel elongation, for the inert cases, or flame front growth, for the reacting cases. The results also compare simulation spark channel and flame growth plots to experimental Schlieren images at different instants in time. This work serves to highlight LESI’s ability to predict the characteristics of discharge and ignition across a variety of operating conditions.« less

Although ubiquitous in modern vehicles, Controller Area Networks (CANs) lack basic security properties and are easily exploitable. A rapidly growing field of CAN security research has emerged that seeks to detect intrusions or anomalies on CANs. Producing vehicular CAN data with a variety of intrusions is a difficult task for most researchers as it requires expensive assets and deep expertise. To illuminate this task, we introduce the first comprehensive guide to the existing open CAN intrusion detection system (IDS) datasets. We categorize attacks on CANs including fabrication (adding frames, e.g., flooding or targeting and ID), suspension (removing an ID’s frames),more » and masquerade attacks (spoofed frames sent in lieu of suspended ones). We provide a quality analysis of each dataset; an enumeration of each datasets’ attacks, benefits, and drawbacks; categorization as real vs. simulated CAN data and real vs. simulated attacks; whether the data is raw CAN data or signal-translated; number of vehicles/CANs; quantity in terms of time; and finally a suggested use case of each dataset. State-of-the-art public CAN IDS datasets are limited to real fabrication (simple message injection) attacks and simulated attacks often in synthetic data, lacking fidelity. In general, the physical effects of attacks on the vehicle are not verified in the available datasets. Only one dataset provides signal-translated data but is missing a corresponding “raw” binary version. This issue pigeon-holes CAN IDS research into testing on limited and often inappropriate data (usually with attacks that are too easily detectable to truly test the method). The scarcity of appropriate data has stymied comparability and reproducibility of results for researchers. As our primary contribution, we present the Real ORNL Automotive Dynamometer (ROAD) CAN IDS dataset, consisting of over 3.5 hours of one vehicle’s CAN data. ROAD contains ambient data recorded during a diverse set of activities, and attacks of increasing stealth with multiple variants and instances of real (i.e. non-simulated) fuzzing, fabrication, unique advanced attacks, and simulated masquerade attacks. To facilitate a benchmark for CAN IDS methods that require signal-translated inputs, we also provide the signal time series format for many of the CAN captures. Our contributions aim to facilitate appropriate benchmarking and needed comparability in the CAN IDS research field.« less

This work employs a novel laser induced fluorescence (LIF) diagnostic to measure fuel dilution in a running single cylinder research engine operated at stochastic pre ignition (SPI) and non-SPI prone conditions. Measurements of LIF based fuel dilution are quantified over a range of engine loads and fuel injection timings for two fuels. The in situ LIF measurements of fuel/lubricant interactions illustrate regions of increased fuel dilution from fuel-wall interactions and is believed to be a fundamental underpinning to generating top ring zone liquid conditions conducive to SPI. Furthermore, a novel level of dye doped in the fuel, between 50 tomore » 500 ppm was used as the fluorescence source, at engine operating speed of 2000r/min from 5 to 18 bar of IMEPg injection timings was swept for two fuels of varying volatility. The direct real time LIF measurements highlight that there are non-linear trends in fuel dilution beyond simple dependencies of fuel volatility, injection duration or injection timing, suggesting that further understanding of spray interaction with engine surfaces and the turbulent field are needed to quantify fuel dilution effects that are conducive to SPI. Moreover, results show the potential of this diagnostic technique as an additional tool for quantifying spray and fuel mixing in fundamental studies deployable across a variety of engine loads from law to full load.« less

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intakemore » charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.« less

Heavy-duty vehicles require expensive after treatment systems for control of emissions such as particulate matter (PM) and nitrogen oxides (NOx) to comply with stringent emission standards. Reduced engine-out emissions could potentially alleviate the emission control burden, and thus bring about reductions in the cost associated with after treatment systems, which translates into savings in vehicle ownership. This study evaluates potential reductions in manufacturing and operating costs of redesigned emission after treatment systems of line-haul heavy-duty diesel vehicles (HDDVs) with reduced engine-out emissions brought about by co-optimized fuel and engine technologies. Three emissions reduction cases representing conservative, medium, and optimistic engine-outmore » emission reduction benefits are analyzed, compared to a reference case: the total costs of after treatment systems (TCA) of the three cases are reduced to 11,400(1.63 cents/km), 9,100 (1.30 cents/km), and 8,800 (1.26 cents/km), respectively, compared to 12,000 (1.71 cents/km) for the reference case. The largest potential reductions result from reduced diesel exhaust fluid (DEF) usage due to lower NOx emissions. Downsizing after treatment devices is not likely, because the sizes of devices are dependent on not only engine-out emissions, but also other factors such as engine displacement. As a result, sensitivity analysis indicates that the price and usage of DEF have the largest impacts on TCA reduction.« less

One of the main factors limiting the efficiency of spark-ignited (SI) engines is the occurrence of engine knock. In high temperature and high pressure in-cylinder conditions, the fuel–air mixture auto-ignites creating pressure shock waves in the cylinder. Knock can significantly damage the engine and hinder its performance; as such, conservative knock control strategies are generally implemented which avoid such operating conditions at the cost of lower thermal efficiencies. Significant improvements in the performance of conventional knock controllers are possible if the properties of the knock process are better characterized and exploited in knock controller designs. One of the methods undertakenmore » to better characterize knocking instances is to employ a probabilistic approach, in which the likelihood of knock is derived from the statistical distribution of knock intensity (KI). In this paper, it is shown that KI values at a fixed operating point for single fuel and dual fuel engines are accurately described using a mixed lognormal distribution. The fitting accuracy is compared against those for a randomly generated mixed-lognormally distributed dataset, and shown to exceed a 95% accuracy threshold for almost all of the operating points tested. Additionally, this paper discusses a stochastic knock control approach that leverages the mixed lognormal distribution to adjust spark timing based on KI measurements. Overall, this more informed knock control strategy would allow for improvements in engine performance and fuel efficiency by minimizing knock occurrences.« less

With the engine technology moving toward more challenging (highly dilute and boosted) operation, spark-ignition processes play a key role in determining flame propagation and completeness of the combustion process. On the computational side, there is plenty of spark-ignition models available in literature and validated under conventional, stoichiometric spark ignition (SI) operation. Nevertheless, these models need to be expanded and developed on more physical grounds since at challenging operation they are not truly predictive. This paper reports on the development of a dedicated model for the spark-ignition event at nonquiescent, engine-like conditions, performed in the commercial CFD code converge. The developedmore » methodology leverages previous findings that have expanded the use and improved the accuracy of Eulerian-type energy deposition models. In this work, the Eulerian energy deposition is coupled at every computational time-step with a Lagrangian-type evolution of the spark channel. Typical features such as spark channel elongation, stretch, and attachment to the electrodes are properly described to deliver realistic energy deposition along the channel during the entire ignition process. The numerical results are validated against schlieren images from an optical constant volume chamber and show the improvement in the simulation of the spark channel during the entire ignition event, with respect to the most commonly used energy deposition approach. Further developmental pathways are discussed to provide more physics-based features from the developed ignition model in the future.« less